Bar ends?

NONE_too_SOFT · 03-29-2009, 02:27 AM

I've never had to deal with this before, but i cant figure out for the life of me how to install my bar ends. I took the one i did have off, and just tried putting the new one on in place. worked fine, but stuck out way too far. i thought i understood the mechanics to it (the mount you screw the actual bar end into screws into the clipon, if im not mistaken) but couldnt adjust that mount at all.

so i go to the otherside, and have the exact opposite problem. the mount was recessed too far back.

Any ideas?

Amber Lamps · 03-29-2009, 07:17 AM

Quote:

Originally Posted by NONE_too_SOFT

I've never had to deal with this before, but i cant figure out for the life of me how to install my bar ends. I took the one i did have off, and just tried putting the new one on in place. worked fine, but stuck out way too far. i thought i understood the mechanics to it (the mount you screw the actual bar end into screws into the clipon, if im not mistaken) but couldnt adjust that mount at all.

so i go to the otherside, and have the exact opposite problem. the mount was recessed too far back.

Any ideas?

Swap them left to right?

Use some stainless washers to shim out the recessed side to match?

Trip · 03-29-2009, 10:54 AM

on the short one, you are going to have to attach the bolt not very far in at all and try to pull that one out some. It's a pain in the ass. If you put the bolt too far in it will expand and it won't budge.

on the long one, do the same with the bolt and beat it in with a rubber mallet to desired distance.

Amber Lamps · 03-29-2009, 12:33 PM

Quote:

Originally Posted by Trip

on the short one, you are going to have to attach the bolt not very far in at all and try to pull that one out some. It's a pain in the ass. If you put the bolt too far in it will expand and it won't budge.

on the long one, do the same with the bolt and beat it in with a rubber mallet to desired distance.

Well,there ya go!

Dave · 03-29-2009, 01:12 PM

yer kidding right?

HRCNICK11 · 03-29-2009, 01:18 PM

If its the stock ones the insert moves. There is a clip on it that digs into the inside of the bar itself.

NONE_too_SOFT · 03-31-2009, 07:36 AM

i was thinking about trying the rubber mallet, but the thing looks threaded, so i figured it turned...

i guess i could use my engineering knowhow to find a way to pull the other one out... i'll probobly kill myself somehow.

Yamerhaw · 03-31-2009, 02:07 PM

Quote:

Originally Posted by NONE_too_SOFT

i was thinking about trying the rubber mallet, but the thing looks threaded, so i figured it turned...

i guess i could use my engineering knowhow to find a way to pull the other one out... i'll probobly kill myself somehow.

could you leave a note for someone else to post up if you do manage to kill yourself replacing bar ends?

HRCNICK11 · 03-31-2009, 02:50 PM

http://fiche.ronayers.com/Index.cfm/...BAR_TOP_BRIDGE

That link might help it has a photo of all the parts involved.

More than likely the insert broke about a inch in if its spins. The bar end and the insert should have half circles that interlock so you can hold the bar end to keep the insert from spining. Lots of times the bar end breaks and takes about 3/4 of a inch of the insert with it. You would need to replace the insert also.

If you need to replace the insert a slide hammer works nice to remove it. There is a one way clip that snaps into a hole in the bar and is damaged when removed.

Amber Lamps · 03-31-2009, 04:12 PM

Quote:

Originally Posted by HRCNICK11

http://fiche.ronayers.com/Index.cfm/...BAR_TOP_BRIDGE

That link might help it has a photo of all the parts involved.

More than likely the insert broke about a inch in if its spins. The bar end and the insert should have half circles that interlock so you can hold the bar end to keep the insert from spining. Lots of times the bar end breaks and takes about 3/4 of a inch of the insert with it. You would need to replace the insert also.

If you need to replace the insert a slide hammer works nice to remove it. There is a one way clip that snaps into a hole in the bar and is damaged when removed.

Ok I'm up to speed now...Would it be better for him just to "beat the insert in further and buy aftermarket,even Suzuki style ends?

03-29-2009, 02:27 AM	#1
NONE_too_SOFT Chopstix / \ Join Date: Feb 2008 Location: Akron OH Moto: 03 CBR RR Posts: 5,350	Bar ends? I've never had to deal with this before, but i cant figure out for the life of me how to install my bar ends. I took the one i did have off, and just tried putting the new one on in place. worked fine, but stuck out way too far. i thought i understood the mechanics to it (the mount you screw the actual bar end into screws into the clipon, if im not mistaken) but couldnt adjust that mount at all. so i go to the otherside, and have the exact opposite problem. the mount was recessed too far back. Any ideas?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-29-2009, 01:12 PM	#5
Dave Chaotic Neutral Join Date: Feb 2008 Location: Cherry Hill NJ Moto: GV1200 Madura, Hawk gt Posts: 13,992	yer kidding right?

03-29-2009, 01:18 PM	#6
HRCNICK11 Canyon Carver Join Date: Nov 2008 Posts: 429	If its the stock ones the insert moves. There is a clip on it that digs into the inside of the bar itself.

03-31-2009, 07:36 AM	#7
NONE_too_SOFT Chopstix / \ Join Date: Feb 2008 Location: Akron OH Moto: 03 CBR RR Posts: 5,350	i was thinking about trying the rubber mallet, but the thing looks threaded, so i figured it turned... i guess i could use my engineering knowhow to find a way to pull the other one out... i'll probobly kill myself somehow.

03-31-2009, 02:50 PM	#9
HRCNICK11 Canyon Carver Join Date: Nov 2008 Posts: 429	http://fiche.ronayers.com/Index.cfm/...BAR_TOP_BRIDGE That link might help it has a photo of all the parts involved. More than likely the insert broke about a inch in if its spins. The bar end and the insert should have half circles that interlock so you can hold the bar end to keep the insert from spining. Lots of times the bar end breaks and takes about 3/4 of a inch of the insert with it. You would need to replace the insert also. If you need to replace the insert a slide hammer works nice to remove it. There is a one way clip that snaps into a hole in the bar and is damaged when removed.