Vortex sucks balls! - Page 7

speedylocksmith · 11-14-2008, 06:26 PM

Quote:

Originally Posted by Ninjakel

Crap chain maintence

ok, i'm guilty to a point. Chain was pretty clean but it was loose.

ceo012384 · 11-15-2008, 10:37 PM

Quote:

Originally Posted by Gas Man

Many do. Theoretically they should be good. But they usually aren't.

Yeah they are always off.

My buddy is going to make some alignment tools... they are rods that go through the axes of your choosing and have little flats on them so you can run a measuring tape.

I.e. put one through the rear axle and one through the swingarm pivot, measure both sides and match the numbers to align the chain.

pickle.of.doom · 11-15-2008, 11:16 PM

All aluminum sprockets wear pretty fast, like Jeeps said, especially with bikes that throw down a lot of torque. Also most of the sprockets out there, no matter which company is selling them, are mainly made by the same company anyway (SUN).

Quick281 · 11-23-2008, 07:03 PM

Quote:

Originally Posted by ceo012384

Yeah they are always off.

My buddy is going to make some alignment tools... they are rods that go through the axes of your choosing and have little flats on them so you can run a measuring tape.

I.e. put one through the rear axle and one through the swingarm pivot, measure both sides and match the numbers to align the chain.

Thats a good idea.

Leon · 11-24-2008, 11:01 AM

Quote:

Originally Posted by Quick281

Thats a good idea.

Off to the lathe to make some tools.

ceo012384 · 11-24-2008, 06:40 PM

Quote:

Originally Posted by Leon

Off to the lathe to make some tools.

Have little tapered cones that slide on the rods that have setscrews in them. You slide those into the axle/pivot/etc holes and the tapering centers them on that axis. Then tighten the set screw and measure the distance between the flats on the end of the rods.

Leon · 11-24-2008, 09:49 PM

Yup, that was the idea that came to mind.

I've made stuff on the lathe in the past.

Like my spike key.

Quick281 · 11-25-2008, 12:29 AM

Thats pretty cool, but since I usually keep my keys in a pocket, I would imagine that could hurt like hell if I ran into something.

speedylocksmith · 11-25-2008, 01:45 AM

Quote:

Originally Posted by Quick281

Thats pretty cool, but since I usually keep my keys in a pocket, I would imagine that could hurt like hell if I ran into something.

I have one that he made. It's not bad at all and unique

BobTheBiker · 11-25-2008, 03:57 AM

I should take some pictures of our "wall of shame" the next time I visit pureacceleration. I swear there are a good half dozen vorjunk rear sprockets, and maybe a few fronts on the wall there, that are missing teeth, or just have pure NUBS or less left on them. off 600's 1000's, 750's, and just yeah. vortex=shit. fuck them, fuck their cheap ass soft aluminum. I'm keepin my STEEL sprockets.

11-15-2008, 11:16 PM	#63
pickle.of.doom el diablo de verde Join Date: Feb 2008 Location: Howell, MI Moto: VTR, CBR, DRZSM Posts: 1,046	All aluminum sprockets wear pretty fast, like Jeeps said, especially with bikes that throw down a lot of torque. Also most of the sprockets out there, no matter which company is selling them, are mainly made by the same company anyway (SUN). __________________ WOS Forums

11-25-2008, 12:29 AM	#68
Quick281 Victim of Blazer Rapage Join Date: Mar 2008 Location: Talkeetna, AK Moto: 06 GSXR 600 Posts: 1,707	Thats pretty cool, but since I usually keep my keys in a pocket, I would imagine that could hurt like hell if I ran into something. __________________ -Alex- Resident TWFix Noob. My 06 GSXR 600 <-- Its Clickable Fools.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-24-2008, 09:49 PM	#67
Leon WERA Yellow Plate Join Date: Nov 2008 Posts: 648	Yup, that was the idea that came to mind. I've made stuff on the lathe in the past. Like my spike key.

11-25-2008, 03:57 AM	#70
BobTheBiker too much time on my hands Join Date: Jul 2008 Location: the northern district of god damn Moto: 01 ZX6R, looking for more now. Posts: 1,802	I should take some pictures of our "wall of shame" the next time I visit pureacceleration. I swear there are a good half dozen vorjunk rear sprockets, and maybe a few fronts on the wall there, that are missing teeth, or just have pure NUBS or less left on them. off 600's 1000's, 750's, and just yeah. vortex=shit. fuck them, fuck their cheap ass soft aluminum. I'm keepin my STEEL sprockets.