Go Back   Two Wheel Fix > In the Garage or Shop > Aftermarket Modding

Reply
 
Thread Tools Display Modes
Old 02-19-2011, 11:30 AM   #1
jtemple
Geek
 
jtemple's Avatar
 
Join Date: Feb 2008
Location: Papillion, Nebraska
Moto: 2011 Husqvarna TE630
Posts: 1,437
Default Garage Door Opener

I have a keychain garage door opener that's about as water resistant as a sock filled with holes. It runs off of an A23 12V battery, and I want to hard wire the guts of it into my bike and mount a switch on the top bar clamp. What I need is some way to make the electronics water resistant. Should I just drill into the case to run wires into it and seal it up with hot glue? Or is there better option?
jtemple is offline   Reply With Quote
Old 02-19-2011, 11:45 AM   #2
Amber Lamps
Moto GP Star
 
Join Date: Mar 2008
Posts: 14,556
Default

Quote:
Originally Posted by jtemple View Post
I have a keychain garage door opener that's about as water resistant as a sock filled with holes. It runs off of an A23 12V battery, and I want to hard wire the guts of it into my bike and mount a switch on the top bar clamp. What I need is some way to make the electronics water resistant. Should I just drill into the case to run wires into it and seal it up with hot glue? Or is there better option?
My absolute favorite way to do this is to remove the battery and run your horn wires to the leads, "T" taps work okay, be mindful of pos/neg and rig the button to be pressed in all the time. Wrap it in tape to seal it and strap it in by the horn/on the horn bracket. Viola, when you pull up to your house, beep the horn and your garage door will open. I really should sell these....
Amber Lamps is offline   Reply With Quote
Old 02-19-2011, 12:15 PM   #3
azoomm
moderator chick

 
azoomm's Avatar
 
Join Date: Feb 2008
Location: Hill Country TX
Moto: Pasta Rockets
Posts: 8,917
Default

Quote:
Originally Posted by Amber Lamps View Post
My absolute favorite way to do this is to remove the battery and run your horn wires to the leads, "T" taps work okay, be mindful of pos/neg and rig the button to be pressed in all the time. Wrap it in tape to seal it and strap it in by the horn/on the horn bracket. Viola, when you pull up to your house, beep the horn and your garage door will open. I really should sell these....
We've done the same thing, except used connections found at West Marine. I've found, if you want something weather-proof - look for something commonly used on a boat
__________________
We have enough youth. How about a fountain of "smart"?

Come Play at the Track!!

http://www.elitetrackdays.com
azoomm is offline   Reply With Quote
Old 02-19-2011, 12:28 PM   #4
Particle Man
Custom User Title
 
Particle Man's Avatar
 
Join Date: Nov 2008
Location: Central NY
Moto: 2003 SV650S
Posts: 14,959
Default

Quote:
Originally Posted by azoomm View Post
I've found, if you want something weather-proof - look for something commonly used on a boat
Same here. Any plugs, connections, etc, I usually use marine grade materials.
__________________
I'm not "fat."
I'm "Enlarged to show texture."


Handle every stressful situation like a DOG: If you can't eat it or hump it, pi$$ on it & walk away.
Particle Man is offline   Reply With Quote
Old 02-19-2011, 12:51 PM   #5
jtemple
Geek
 
jtemple's Avatar
 
Join Date: Feb 2008
Location: Papillion, Nebraska
Moto: 2011 Husqvarna TE630
Posts: 1,437
Default

Quote:
Originally Posted by Amber Lamps View Post
My absolute favorite way to do this is to remove the battery and run your horn wires to the leads, "T" taps work okay, be mindful of pos/neg and rig the button to be pressed in all the time. Wrap it in tape to seal it and strap it in by the horn/on the horn bracket. Viola, when you pull up to your house, beep the horn and your garage door will open. I really should sell these....
On the sportbike, that's how I'd have done it. On the TE, the bar clamp I'm getting (it comes with the handguard I'm ordering) comes with switch mounts. The switches are only $4 each. My plan is to set up a dedicated circuit, to avoid cutting into the wiring harness.
jtemple is offline   Reply With Quote
Old 02-19-2011, 12:56 PM   #6
Trip
Hold mah beer!
 
Trip's Avatar
 
Join Date: Feb 2008
Location: 80 Miles South of Moto Heaven
Moto: 08 R1200GS
Posts: 23,268
Default

Hot glue will seal something. So will silicone.

My ass is too cheap to use marine grade. Especially for the amount of connections I make on my property for Christmas. Never had an issue with snow or rain.

For a street motorcycle (dirt riders need not apply since they have stream crossing that could be an issue), you are looking more for a barrier than a sealant. Water can intrude as long as it doesn't bridge any connections ie: standing water and such that boats have to worry about. And you also aren't as worried about contaminants like salt from salt water rusting shit, so tape would also work fine for street moto applications.

We are talking about the TE though, so seal it.

Last edited by Trip; 02-19-2011 at 01:03 PM..
Trip is offline   Reply With Quote
Old 02-19-2011, 01:02 PM   #7
jtemple
Geek
 
jtemple's Avatar
 
Join Date: Feb 2008
Location: Papillion, Nebraska
Moto: 2011 Husqvarna TE630
Posts: 1,437
Default

Quote:
Originally Posted by Trip View Post
Hot glue will seal something. So will silicone.

My ass is too cheap to use marine grade. Especially for the amount of connections I make on my property for Christmas. Never had an issue with snow or rain.
I have both. I'll probably try the silicone first and just seal up the existing enclosure. It's just a keyfob door opener.
jtemple is offline   Reply With Quote
Old 02-19-2011, 02:07 PM   #8
goof2
AMA Supersport
 
goof2's Avatar
 
Join Date: Feb 2009
Posts: 4,756
Default

If you don't want to dump silicone all over the electrical components (in case you need to get to dip switches or programing buttons) pick up what is called a heat shrink end cap. Stick the electrical guts in the end cap with the wires sticking out and shrink it down. Then you only have to seal where the wires are coming out. You could also use regular heat shrink tubing, which should be easier to find, and just seal up both ends.
goof2 is offline   Reply With Quote
Old 02-19-2011, 04:39 PM   #9
jtemple
Geek
 
jtemple's Avatar
 
Join Date: Feb 2008
Location: Papillion, Nebraska
Moto: 2011 Husqvarna TE630
Posts: 1,437
Default

Eh, the fob is cheap. If it comes down to that I'd just buy a new one.
jtemple is offline   Reply With Quote
Old 02-20-2011, 07:49 PM   #10
Papa_Complex
Nomadic Tribesman
 
Papa_Complex's Avatar
 
Join Date: Nov 2008
Location: Brampton, Canada
Moto: '09 ER-6n
Posts: 11,150
Default

Open up the remote case to add a connector for a parallel door switch then put the whole thing in a weather sealed iPod case, like one of the units sold by Pelican. It's about as water tight as you can get. Just toss in a couple of desiccant packs, to keep condensation from forming.
__________________
"Everything's better with pirates." - Lodge, "Dorkness Rising"

http://www.morallyambiguous.net/
Papa_Complex is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:34 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.