12-06-2009, 10:47 PM | #1 |
Viff6N Mutated Warrior
Join Date: Mar 2009
Location: Texas
Moto: '01 Honda VFR 800 & '09 ER-6N
Posts: 8,704
|
Crap crap crap and more crap
Vehicle: Got a coolant leak at my firewall where the two hoses go to my heater core. Also a main hose is leaking. Starter is going to shit cause the wiring is crappy. I re-used the old gaskets on my T-case and its leaking like a sieve now. My fault on that. I just stuck the new gears in to do a test run and never dropped it again.
Bike: Found some oilish crap plastic behind front wheel, under front wheel plastic, on tire, etc. Pretty sure its not from the bike cause I couldnt find any wet spots. I guess I rode over an oil spill. LOL The main coolant hose that connects both my rads is super soft and crimping itself. Rear brake resevoir is low. All brake pads probably need to be replaced. I dont want to change my fluid until I changed pads but I dont want to spend money on new brakes. Last edited by Rangerscott; 12-07-2009 at 02:48 AM.. |
12-06-2009, 10:49 PM | #2 |
Canyon Carver
Join Date: Nov 2008
Location: Pensacola, FL
Moto: The v-twin trifecta
Posts: 437
|
Heater core replacement = the suck
Time to trade it in. |
12-06-2009, 11:03 PM | #3 |
Viff6N Mutated Warrior
Join Date: Mar 2009
Location: Texas
Moto: '01 Honda VFR 800 & '09 ER-6N
Posts: 8,704
|
|
12-07-2009, 12:49 AM | #4 |
I'm so much cooler online
Join Date: Nov 2008
Location: Cartersville, GA
Moto: 06 FZ1
Posts: 1,436
|
It's it's leaking in the engine compartment you're golden. If it's leaking inside the car then, new core = the suck
|
12-07-2009, 02:06 AM | #5 |
Moto GP Star
Join Date: Nov 2008
Posts: 11,022
|
|
12-07-2009, 02:22 AM | #6 |
I give Squids a bad name
Join Date: Mar 2008
Location: Fly Over State
Moto: 1996 CBR600 F3 (AKA the Flying Turd)
Posts: 4,742
|
No shit. My S10 heater core went out and I had to remove my entire inside, dash, steering wheel, etc to get to it. Dumbest part was I had a 1998 S10 and the radiator shop showed 2 kinds of heater cores for S10s. I could get the one from 1980something-1997 or 1999-latest model. 1999+ was $130 and the 1997- was $30. I got the $30 one and the only difference was the two pipes where bent different so I switched the old pipes to the new heater core and it worked perfect.
__________________
lifts - R.I.P. |
12-07-2009, 02:49 AM | #7 |
Viff6N Mutated Warrior
Join Date: Mar 2009
Location: Texas
Moto: '01 Honda VFR 800 & '09 ER-6N
Posts: 8,704
|
Ya'll are a bunch of non-wrenching wieners! Just more things to add on to the To-Do list.
Going to go get a couple feet of rad hose and some speed bleeders. |
12-07-2009, 03:20 AM | #8 |
WSB Champion
Join Date: Nov 2008
Location: Anaheim, CA
Moto: 2009 Kawi ZX6R
Posts: 5,570
|
Just bypass the heater core and buy a 12V little car heater.
__________________
Train Hard Ron Paul - 2012 Mark of Excellence GM |
12-07-2009, 03:40 AM | #9 |
Viff6N Mutated Warrior
Join Date: Mar 2009
Location: Texas
Moto: '01 Honda VFR 800 & '09 ER-6N
Posts: 8,704
|
|
12-08-2009, 05:29 AM | #10 |
too much time on my hands
Join Date: Jul 2008
Location: the northern district of god damn
Moto: 01 ZX6R, looking for more now.
Posts: 1,802
|
heater cores ARENT fun. I swear up and down that when mine starts leaking, I do not care, that shit ISNT getting replaced. I'm absolutely bypassing the heater.
|
Bookmarks |
|
|