Raising the SV - Page 2

ontwo · 10-02-2009, 12:15 PM

Quote:

Originally Posted by Particle Man

Do yourself a favor if and while it's up on the front stand, throw a jack under the engine block and jack the block up to take pressure off the cushion lever and so the swingarm can move freely... not such an issue taking the bolts out but it will help a TON when you're putting stuff back together.

I think I invented several swear words until I figured that little trick out.

As for the front forks, there should be just about 1/4 of an inch sticking out of the top triple clamp (maybe a little less).

That's the way I did it with the 10. Just be sure not to jack it too much and tip it off the rear stand (don't ask me how I know that)

psychochild28 · 10-04-2009, 01:36 AM

So I went to Hokie's place so they could work on it and come to find out the guy that lowered it over torqued a LOT!

So they're going to look for a new bolt for me and we're going to try it again this week.

Thanks so much again Hokie!

Particle Man · 10-04-2009, 09:45 PM

Quote:

Originally Posted by psychochild28

So I went to Hokie's place so they could work on it and come to find out the guy that lowered it over torqued a LOT!

So they're going to look for a new bolt for me and we're going to try it again this week.

Thanks so much again Hokie!

another person who didn't actually follow the torque specs in the service manual, eh?

Trip · 10-04-2009, 11:25 PM

That's why I hate taking my shit to dealers, they always overtorque

Kerry_129 · 10-04-2009, 11:27 PM

More than just overtorqued - likely done with a healthy impact wrench. She said the PO installed the links.
It didn't appear corroded at all, but locked to the point I think it likely would have sheared or stripped the threads before loosening, and I definitely wouldn't trust it for re-use. We'll track down a bolt & have it on hand to swap tomorrow or Tue evening.

Jenna - the hardware you need is #9 & 11 shown here. http://www.mrcycles.com/fiche_sectio...008&fveh=19002
I made a mistake when I wrote down the bolt info. It's actually M12x1.25 x 100mm long, and grade 9.8 or 10.9

I'll see what I can find 1st thing in the morning.

Trip · 10-04-2009, 11:33 PM

I think I actually have that bolt somewhere, but it would take years to find. I have another shock as well.

Make sure you inspect the shock threads carefully, if something is torqued that bad, it's going to damage the threads if you snap it. If worse comes to worse and you damage the threading, I can hook you up on a good deal on another stock shock, cause I know I have one and I know where it is. Thats the bad thing about putting threading on the equipment itself. I have a big issue at work I am dealing with where the threading on a motor got damaged from the torqued value provided by the vendor and the motors are ripping themselves off the equipment. This motor is a lot more powerful than a SV though.

Kerry_129 · 10-04-2009, 11:42 PM

Fortunately it's just the bottom linkage bolt/nut which sandwiches the dogbones & needle-bearing sleeve. I'll inspect the sleeve, of course, but they're hardened/ground so I doubt they 'mushroomed' at all. I have an identical flanged nut which I cannibalized off a HawkGT project-bike, but the bolt was only 80mm. Good looking out though!

Trip · 10-04-2009, 11:44 PM

Quote:

Originally Posted by Kerry_129

Fortunately it's just the bottom linkage bolt/nut which sandwiches the dogbones & needle-bearing sleeve. I have an identical flanged nut which I cannibalized off a HawkGT project-bike, but the bolt was only 80mm.

ah thats the one with the nut, I always get those two mixed up.

psychochild28 · 10-05-2009, 09:40 AM

Quote:

Originally Posted by Kerry_129

More than just overtorqued - likely done with a healthy impact wrench. She said the PO installed the links.
It didn't appear corroded at all, but locked to the point I think it likely would have sheared or stripped the threads before loosening, and I definitely wouldn't trust it for re-use. We'll track down a bolt & have it on hand to swap tomorrow or Tue evening.

Jenna - the hardware you need is #9 & 11 shown here. http://www.mrcycles.com/fiche_sectio...008&fveh=19002
I made a mistake when I wrote down the bolt info. It's actually M12x1.25 x 100mm long, and grade 9.8 or 10.9

I'll see what I can find 1st thing in the morning.

Thank you! You guys are awesome!

psychochild28 · 10-21-2009, 01:53 AM

And the SV is back to stock height!

Thank you so much Kerry! I owe you guys big time.

Next step riding it this weekend!

10-04-2009, 11:27 PM	#15
Kerry_129 Semi-reformed Squid Join Date: Nov 2008 Posts: 531	More than just overtorqued - likely done with a healthy impact wrench. She said the PO installed the links. It didn't appear corroded at all, but locked to the point I think it likely would have sheared or stripped the threads before loosening, and I definitely wouldn't trust it for re-use. We'll track down a bolt & have it on hand to swap tomorrow or Tue evening. Jenna - the hardware you need is #9 & 11 shown here. http://www.mrcycles.com/fiche_sectio...008&fveh=19002 I made a mistake when I wrote down the bolt info. It's actually M12x1.25 x 100mm long, and grade 9.8 or 10.9 I'll see what I can find 1st thing in the morning. Last edited by Kerry_129; 10-04-2009 at 11:31 PM..

10-04-2009, 11:42 PM	#17
Kerry_129 Semi-reformed Squid Join Date: Nov 2008 Posts: 531	Fortunately it's just the bottom linkage bolt/nut which sandwiches the dogbones & needle-bearing sleeve. I'll inspect the sleeve, of course, but they're hardened/ground so I doubt they 'mushroomed' at all. I have an identical flanged nut which I cannibalized off a HawkGT project-bike, but the bolt was only 80mm. Good looking out though! Last edited by Kerry_129; 10-04-2009 at 11:44 PM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-04-2009, 01:36 AM	#12
psychochild28 Banned Join Date: Feb 2008 Location: On a bus Moto: SV 650S Posts: 857	So I went to Hokie's place so they could work on it and come to find out the guy that lowered it over torqued a LOT! So they're going to look for a new bolt for me and we're going to try it again this week. Thanks so much again Hokie!

10-21-2009, 01:53 AM	#20
psychochild28 Banned Join Date: Feb 2008 Location: On a bus Moto: SV 650S Posts: 857	And the SV is back to stock height! Thank you so much Kerry! I owe you guys big time. Next step riding it this weekend!