Electrical accessories, project completed

derf · 03-31-2009, 12:06 AM

So a few weeks ago I started another thread here about adding some power adapters to my bike. So far I added one, with plans to add one more under my rear seat. The plan was to tap into the stock electrical system as little as possible, in fact there is just one connection to the stock system, at the horn power wire (the horn wont mess with any other systems, thanks Phenix_Rider), the rest of the system is a complete stand alone wire harness.

Here is the scematic that I followed. Plus I added a fuse between the battery and the fuse box.

Anyway here is the start of the bracket that holds the power outlet and the volt/clock. this was actually the 3rd attempt, the first 2 I had issues with stuff rubbing and or getting in the way of either the handlebars or the clutch cable. I wound up deciding to put the power outlet out the side vs up or in the center, this looks like it will work the best.

Here is a picture of the almost finished product where the power outlet plugs in the side.

This is the power system under the seat. I made a bracket to move the CPU over and hold the electrical box. Notice the relay switch above the fuse box, and the main fuse to the left of the fuse box.

This is the finished Dash, notice the key is in the off position and all the LED's aren't lit.

This is the finished Dash, notice the key is in the on position and all the LED's are lit. SUCESS!!!

Comment on my awesomness BITCHEZZZZ!!!!!!!

t-homo · 03-31-2009, 05:30 AM

Wouldn't it have been easier to just get two harnesses similar to what the battery tender uses and put those adapters on the ends?

rogue · 03-31-2009, 06:38 PM

Looks good!

derf · 03-31-2009, 08:54 PM

Quote:

Originally Posted by t-rock

Wouldn't it have been easier to just get two harnesses similar to what the battery tender uses and put those adapters on the ends?

Yes, but i wanted to have the electrics right that way I don't risk the bike catching on fire if there is a short or an overload for any reason.

Mr Lefty · 03-31-2009, 10:52 PM

Quote:

Originally Posted by derf

Yes, but i wanted to have the electrics right that way I don't risk the bike catching on fire if there is a short or an overload for any reason.

but where's the fun in that?

t-homo · 03-31-2009, 11:10 PM

Quote:

Originally Posted by derf

Yes, but i wanted to have the electrics right that way I don't risk the bike catching on fire if there is a short or an overload for any reason.

That makes sense too.

derf · 03-31-2009, 11:13 PM

Quote:

Originally Posted by ebbs15

but where's the fun in that?

I did put a small pinhole in the fuel tank and added a pilot light, which should brighten up my day

Mr Lefty · 04-01-2009, 07:54 AM

that's the spirit!

derf · 04-02-2009, 01:17 AM

I did realize that i forgot to add a spot on the negative to plug in extra ground locations. That is something that I will have to add in later as a way of expanding my electrical accessories.

t-homo · 04-02-2009, 01:17 AM

You are a clever mother fucker.

03-31-2009, 12:06 AM	#1
derf token jewboy Join Date: Nov 2008 Moto: CBR 900, KLR ugly ass duckling, Gas Man Posts: 10,799	Electrical accessories, project completed So a few weeks ago I started another thread here about adding some power adapters to my bike. So far I added one, with plans to add one more under my rear seat. The plan was to tap into the stock electrical system as little as possible, in fact there is just one connection to the stock system, at the horn power wire (the horn wont mess with any other systems, thanks Phenix_Rider), the rest of the system is a complete stand alone wire harness. Here is the scematic that I followed. Plus I added a fuse between the battery and the fuse box. Anyway here is the start of the bracket that holds the power outlet and the volt/clock. this was actually the 3rd attempt, the first 2 I had issues with stuff rubbing and or getting in the way of either the handlebars or the clutch cable. I wound up deciding to put the power outlet out the side vs up or in the center, this looks like it will work the best. Here is a picture of the almost finished product where the power outlet plugs in the side. This is the power system under the seat. I made a bracket to move the CPU over and hold the electrical box. Notice the relay switch above the fuse box, and the main fuse to the left of the fuse box. This is the finished Dash, notice the key is in the off position and all the LED's aren't lit. This is the finished Dash, notice the key is in the on position and all the LED's are lit. SUCESS!!! Comment on my awesomness BITCHEZZZZ!!!!!!! __________________ Last edited by derf; 03-31-2009 at 12:27 AM..

04-02-2009, 01:17 AM	#9
derf token jewboy Join Date: Nov 2008 Moto: CBR 900, KLR ugly ass duckling, Gas Man Posts: 10,799	I did realize that i forgot to add a spot on the negative to plug in extra ground locations. That is something that I will have to add in later as a way of expanding my electrical accessories. __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-31-2009, 05:30 AM	#2
t-homo WSB Champion Join Date: Feb 2008 Location: Springfield, MO Posts: 7,146	Wouldn't it have been easier to just get two harnesses similar to what the battery tender uses and put those adapters on the ends?

04-01-2009, 07:54 AM	#8
Mr Lefty TWFix Legend Join Date: Feb 2008 Location: Denver CO Moto: 01 BMW F650GS Dakar Posts: 15,677	that's the spirit!